Busbars of FTG

At FTG, flexible systems are products for power distribution that can be adapted to individual requirements on site by planners and fitters in almost any way. The Auxigaine busbar enables any number of poles, is installed at the height of the control cabinet – which all flexible systems have in common – and inputs and outputs can be added or removed in an extremely simple way.

  1. Auxigaine
  2. Auxibus
  3. Busspeed
  4. AuxiClic
  5. FCBeasy
  6. Easyvation
  7. Easybreak

Auxigaine

Auxigaine describes an extremely flexible and versatile system to set up individually adapted busbars. A modular system is used to provide rails with any number of poles.
Standard length of up to 1.90 m permits use as permanently energised rail for the entire height of switchboards. Every other dimension is possible as well, of course. Apart from a gigantic modular system, rails can be pre-wired for standard applications in the factory of the manufacturer. Auxigaine can be mounted on to a back panel as well as on to DIN rails using the mounting brackets intended for the purpose. Various conductors are available permitting the rails to be loaded up to 125A.

Auxibus

Flexible system with cover for locking crimp plugs: Auxibus is a flexible two-pole and four-pole busbar that supplies a range of modular devices. The maximum load capacity for each output is 36 A. Each connector locks automatically, so that a high level of security is guaranteed and there is no risk of direct contact due to IP20.

Load capacity:

  • Phase rail: 32 A or 63 A | 690 V AC / DC
  • Short-circuit power: Ipk 10,500 A | Icw 7,400 A | 60 ms
  • Connector 2.5 mm²: 20 A
  • Plug 6 mm²: 36 A

BusSpeed

The flexible control voltage busbar system “BusSpeed”, which is suitable for four phases, is usually used in control cabinet construction, where the need for individual solutions for power distribution and connection is required. A faster and uncomplicated infeed by flexible cables when there is a variation of different levels of
equipment is quickly implemented, without saving space for unneeded cable ducts.

The construction of a live power busbar allows a vertical and horizontal installation using a selection of different mounting brackets for a direct mounting on the panel. Installations are expandable and the busbar system is available with a length till 1,855 meters. With the construction of the live power busbar with up to four poles including marking on the mounting brackets, any number of infeeds is possible. For the need of a shorter construction, the live power busbar can be sawed to individual lengths or is
delivered pre-assembled directly from the factory. A separation of the busbar to divide the potential is easily possible by a small separating plate.

Depending on application BusSpeed busbars are available in bright brass and tinned copper for voltages from 32 A until 125 A.

AuxiClic

Auxiclic is a 250 A busbar that supplies a range of modular devices. The maximum load capacity for each output is 63 A. Each connector locks automatically, so that a high level of security is guaranteed and there is no risk of direct contact due to IP20.

Load capacity:

  • Busbar: 250 A / 690 V
  • Short circuit power: Ipk: 61 kA / Icw: 10 kA /1 s
  • 6 mm² Plug: 40 A
  • 10 mm² Plug: 63 A

Modularity:

  • Infeed by cable with ring cable lug, flexible busbars or directly on the rail system.
  • Due to its high strength, Auxiclic can be used as a rail support.
  • Lengths: 12, 24, 36 modules
  • Mounting on side in switchboards or on a doubled Din rail.

FCBeasy

Busbar – flexible and individual configurable

  • Universally applicable for the following end devices: FI circuit breaker / FI-LS, line circuit breaker, overvoltage protection
  • in 8,9 mm module width freely configurable
  • configuration of conneting lugs without need of breaking them out
  • sawable

Easyvation

The most flexible solution for electricians who want to react quickly and easily to customer requirements. The sawable Easyvation busbar in one to three-pole versions are the perfect tool in the service area for maximum flexibility. For extensions or changes of the system you realize by using the Easyvation busbars most individual solutions directly on site. This system gives your customers a secure and compact solution without waiting times. Also current requirements, such as fire circuit breaker applications can be realized very quickly.

Characteristics

  • flexible busbar system
  • sold by meter 
  • assembly by sawing the busbar
  • configurable by breaking off the lugs
  • combinable
  • no cutting of copper necessary
  • no oddments
  • only low storage requirements
  • 10 or 16 mm²
  • up to 130 A
  • 690 V AC/DC
  • pin or fork
  • material: polycarbonate

Easybreak

The new single phase Busbar of FTG „EasyBreak“ can be customized to fit specific applications due to indentations on the busbar that allow it to be snapped off cleanly.
EasyBreak is suitable for use with devices with a 17.8 mm pitch and are usable with our without insulation. They are available in 16 mm², 25 mm² and 35 mm² amp
ratings with a maximum operating voltage of 1500 V DC.

EasyBreak accessories include feeding terminals, insulation cover, end caps and protection cover for a complete product solution.

Request a quote now!

Friedrich Göhringer Elektrotechnik GmbH
Gerwigstrasse 8
78098 Triberg, Germany

Phone: +49 (0) 7722-9636-0
Fax: +49 (0) 7722-9636-36
E-Mail: info@ftg-germany.de

Office hours:
Mon. - Thu. 7.00 – 16.00 Uhr
Fri. 7.00 – 15.00 Uhr

Product range of FTG

Contact

Friedrich Göhringer
Elektrotechnik GmbH
Gerwigstrasse 8
78098 Triberg, Germany

Phone +49 (0) 7722-9636-0
Fax +49 (0) 7722-9636-36
info@ftg-germany.de